The ENH200 features high transmitted output power, high receivable sensitivity and built-in dual polarization directional antenna. The high power can extend wireless range coverage. The dual polarity antenna allows installer to choose the best orientation to avoid interference, thus maximizing performance and stability.
Supporting highly secure WPA/WPA2 encryption and MAC address filter ensure an uncompromised network security. Furthermore the MAC address filter allows administrator select exactly which client stations can access to your network or not. The RSSI signal strength indicators, PoE injector, mast strap and wall mount accessories that come with the pack makes installation an easy work.
EnGenius’ ENH200 is a perfect solution for integrators and installers to establish building-to-building wireless network connection; for service provider to use as a high performance CPE; for IP security camera installer deploying camera at the outdoor environment.
The following list summarizes the key features of the ENH200:
Can I downgrade firmware safely with this product?
Yes
Cannot get into the device from my computer? Basic setting check
- Make sure you are directly connected to the unit.
- Do not have a switch or router in between and do not connect wirelessly.
- Make sure your power injector/adapter is on, power is going to the unit, and the “network” side is going to your computer.
- Make sure your computer is set to a static IP address of 192.168.1.10.
- Type in 192.168.1.1 using Internet Explorer.
How far can I go using POE (power over Ethernet)?
The device uses non standard injector voltage. Limit distances to 300 feet or less. Do not connect this unit to any 802.3af PoE switch!
How to change the IP Address?
The default IP address is 192.168.1.1. This IP address is typically in conflict with many routers out in the market. You will need to change the IP address manually to an IP address that is different but part of the same network. This means if your router IP address is 192.168.1.1, you should change the device to 192.168.1.2, for example. We recommend you change the IP address before other settings. You change your IP address in the “LAN” section in the GUI.
How to reset the device?
Locate the reset button next to the CAT5 (RJ45) connection. Press and hold the reset button for 10 seconds and then let go. You should see your 10/100 LAN connection at your computer go away and then come back. That will confirm a reset has occurred. The unit settings should all be back to default including its IP address of 192.168.1.1.
How to setup AP WDS Repeater?
Check here to download the setup instructions
How to setup the device under Apple MAC OS X environment?
1. Go to "System Preferences"
2. In the "System Preferences" window, under the "Internet & Network" heading, click on "Network"
3. On the left side, select the network interface you wish to configure. Select a setting from the "Configure" drop-down menu
4. If configuring a static IP address, select "Manually" and then fill in the IP address and Subnet Mask fields, then click "Apply". If configuring to use a DHCP assigned IP address, select "Using DHCP" and then click "Apply"
How to setup WDS Bridge?
Check here to download the setup instructions
I cannot connect or maintain a log in to the device?
We recommend using internet explorer with at least IE7 or higher. Make sure you have latest version of Java script.
I have terrible range, what is wrong?
Make sure the antenna switch is set to “internal” unless using an external antenna.
What distance in kilometers (km) should I set the device to?
Default is 1km. If you are setting up long distance point to point links, the time it takes the radio wave to get there needs to be considered for proper handshaking (ACK response). This window should be accurate within 5 kilometers. In other words if you have a 5 kilometer link, ideally you should set it to 5km, but a setting of 1km to 10km should keep you in an acceptable window. For short distances, keep this to 1km.
What is a point-to-point link setup?
One unit would need to be in AP mode while the other in CB mode. The AP should be connected directly to the routers LAN port, and the other will be in Client Bridge Mode linking back to the AP. The Client side will then provide a WIRED connection for users of the remote location. You can choose to connect this wired connection to just one PC, or to a switch, hub, or another wireless access point for multiple users at the remote location.
What is Client Bridge (CB) Mode?
A client connects to an access point. Your laptop is a client. A bridge is something that connects two “wired” networks together. A client bridge therefore is a radio that wirelessly bridges two networks. The Ethernet port of the 2610 in CB mode provides the wired connection to the remote location. This Ethernet port can directly connect to a single PC, a hub, a switch, or another router.
What is considered a “good” signal?
The signal meter is not available in AP mode. In CB mode, under connection status, a signal of -74dbm or better is a good signal. It’s important to understand which direction numerically is a better signal. Dbm’s are referenced to 1 milliwatt. 1mW = 0dbm. A stronger signal would be a positive number and a weak signal would be a very negative number. For example, a -50dbm signal is stronger signal than -92dbm.
What is spanning tree protocol?
When there are several possible paths a packet can route to (redundant links for increased reliability for example), a loop can occur (jamming up the network). It is used to prevent these loops.
What is the default gateway?
The default gateway is your router’s IP address. The default gateway information is not required, but is recommended.
What is the default user name and password to log into this device?
Log in name is “admin” and password is “admin” by default.
What is WDS Mode?
Stands for Wireless Distribution System. Allows access points to link together and provide repeating. Note however, this repeating comes at a cost of reduced bandwidth. Bandwidth will be reduced by 30-40%, and it is recommended that NO multiple repeating hops be done for this reason.
What type of antenna connector is needed if using a pigtail and external antenna?
The connector type on the 2610 (5610) is an RP-SMA female, so a pigtail cable would need an RP-SMA male. External antennas and coax need to be 50 ohms with 802.11g 2.4GHz frequency (for the 2610) and 802.11a 5GHz frequency (for the 5610).
Download the brochure for the Engenius ENH200 Business Class Long Range Wireless Outdoor Client Bridge Access Point.
Model: ENH200 - Engenius ENH200 Business Class Long Range Wireless Outdoor Client Bridge Access Point
EyeSpyPro.com 101 S. Coit Rd., Suite 36-235, Richardson, TX 75080 USA
Phone: 1-949-791-7904 - FAX: 1-800-862-6120
All clients who purchase from this website agree to all terms and conditions in our Shipping, Returns/Cancellations, Payments, and Warranty links above.
With thousands of products, and dozens of suppliers, there is no guarantee your product will be in stock when you order it, so if its critical you need it right away, please call us @ 1-949-791-7904 before you make your order to confirm it is available and not out of stock or backordered.
Make sure you call us if you have any questions about selecting the correct product to fit your needs before you order, as any custom built hidden cameras, open software or fluid detection devices, boxes with the seal broken, vehicle trackers, and bug detectors are not refundable or returnable unless defective. We are here to assist you, and if you have ANY questions, please call us before you order @ 1-949-791-7904.
30 Day Satisfaction Guarantee: If for any reason you are unhappy with your purchase, you may return it for an exchange or a credit towards any other product within 30 Days,
no questions asked. In order to provide you with high quality products, we do not issue any refunds unless the product arrives defective.
Not responsible for typographical or illustrative errors. Prices, specifications, and images are subject to change without notice.
EyeSpyPro is not responsible for any shipment that is seized by any Government Customs or Border Protection Agency. We are not responsible for any duties, import fees, taxes, VAT charges, or any other fee that you are charged to ship it to you.
Any camera that is not advertised as a day/night, low light, or low lux camera will not perform well in low light, and not at all in the dark. Make sure you know what you are ordering before you order it, and feel free to call us @ the number above or send us an email using the Contact link above.
Do not buy any infrared illuminator if your camera is not an IR camera. It has to have a removable IR-Cut filter that slides out of the way at night for the camera to recognize the IR.
Shipping prices are for one small item. If you order more than one small item, including complete systems, we will adjust the order and charge the actual shipping price.
EyeSpyPro.com does not endorse any of our products for illegal activities. EyeSpyPro.com is not responsible or liable in any way for any damage, vandalism, theft, or any other action that may occur while a EyeSpyPro.com product is in use by the purchaser.